Standards For Power Electronics ( Ansi ) - 2392 Words

Standards for Power Electronics Gration D’silva Dept. of Electrical and Computer Engineering Texas Tech University, Lubbock, TX 79401 USA Telephone: (806) 773-4727; E-mail: gration.dsilva@ttu.edu Abstract— this paper presents a brief overview of standards for power electronics. All the standards presented in this paper are currently active and are approved by the Institute of Electrical and Electronics Engineer Standards Association (IEEE-SA) and American National Standards Institute (ANSI). Keywords—IEEE Standards, ANSI, Power Electronics I. INTRODUCTION The tremendous advancements in modern technology have necessitated the regulation of these technologies so that they meet the required threshold as set by the standardization bodies like the Institute of Electrical and Electronics Engineer Standards Association (IEEE-SA), American National Standards Institute (ANSI). Whenever a new product is launched it has to meet the standards so that they perform as intended. This is very important for the safety of the users and their environment, facilitate interoperability, uniformity in design, testing methods, installation and help make our lives easier. The purpose of standards is to establish certain quality to meet technical, safety, societal, regulatory and market needs. Also standards are the catalysts for technological innovation which are developed based on guiding principles of consensus, due process and within the ethical limits [1]. Standards help making our livesShow MoreRelatedEssay on Cis 5051642 Words   |  7 PagesSelect one (1) of the working groups in the IETF or IEEE and briefly summarize what this group is working on. â€Å"Working groups chartered by the IETF carry out the actual development of new standards and protocols for the Internet. Membership in a working group is voluntary; any interested party may participate. During the development of a specification, a working group will make a draft version of the document available as an Internet Draft, which is placed in the IETFs Internet DraftsRead MoreCable Codes Essay690 Words   |  3 PagesRobin Prather NT1310 Week 2 Exercise April 10, 2013 Cabling Design, Standards, Codes and Definitions 1. American National Standards Institute (ANSI) Five engineering societies and three U.S. government agencies founded the American National Standards Institute (ANSI). ANSI’s mission is to encourage voluntary compliance with standards and methods. 2. Electronic Industries Alliance (EIA) The EIA is organized along speciï ¬ c product and market lines that allow each EIA sector to be responsiveRead MoreA Brief Note On Industrial Products And Safety955 Words   |  4 PagesIndustrial Products and Safety When you are on the job, there is nothing of greater importance than your safety and that of your crew. Safety becomes even more critical when the dangers of height, machinery, chemicals, and power tools are added into the equation. Further, there are times when the job site is in a public location, adding a plethora of safety hazards into the mix. Ensure you are fully equipped with highly visible alerts and warning signs, devices, and barriers. The better a workRead MoreInformation Technology Audit1278 Words   |  6 Pagesexamining the effectiveness of their technical and procedural controls to minimise risks. IT audits are also known as automated data processing (ADP) audits and computer audits or IS, IT or ICT auditing and systems auditing. They were formerly called electronic data processing (EDP) audits History of IS Audit The concept of IT auditing was formed in the mid-1960s. Since that time, IT auditing has gone through numerous changes, largely due to advances in technolog y and the incorporation of technology intoRead MoreRadio Communications For Public Safety1248 Words   |  5 PagesDecember 23, 2016 Introduction Standards need to be set in order to handle current capabilities and handle the demands of what is to come. Standards that come with radio communication have been around for a while and one of those standards includes Public safety radio services. This standard was created for a given scenario were the government would have to send out a message to inform the public. Any agencies that deal with public safety are required to meet this standard. You may here these messagesRead MoreBenefits Of Cable Technology936 Words   |  4 PagesTIA/EIA-606-B standards, and as designed by Panduit to be used for the specific Product. All conduits and inner duct shall be labeled as well. Panduit labels shall be used for all labeling as required by this scope of work, no exceptions. If any other label Manufacturer is used, Contractor shall replace at no expense to Choctaw Nation before final payment. †¢ All dedicated telecommunications grounding bus bars shall be labeled. †¢ Cross-connect fields shall be labeled according to ANSI/TIA/EIA 606-BRead MoreFiber Cable, Tools, And Test Equipment872 Words   |  4 Pages(cisco.) The cost of each individual server will be $2,397, and a total of $47,940 for total project costs prices retrieved from cisco. †¢ The following products as well as the cabling structure will follow the ANSI/TIA-568-C standards and all cable support will comply with NED standards. First floor design The following details are of the design: †¢ Will consist of 200 workstations †¢ Total of 200 people. †¢ There is a total of nine rooms. †¢ 1 storage room †¢ 2 production rooms AB †¢ 1 communicationRead MoreReflection About the Poem Through Education, the Country Received Light3205 Words   |  13 Pages10BaseT Ethernet requires at least Level 3 cable. Many sites now install only Level-5 UTP, even though level 4 is more than sufficient for 10BaseT, because of the greater likelihood that emerging high-speed standards will require cable with better bandwidth capabilities.  Ã‚   Crossover Cable - standard Ethernet cables are straight-thru.   Pin 1 on one end connects to Pin 1 on the far end, Pin2 to Pin2, and so on.   There are only 4 pins that are used, since you only need two wires for transmit, and twoRead MoreElectronic Product Code Upc And Optical Character Recognition Ocr1600 Words   |  7 Pageslink for identification. At start the main hurdle in the deployment of RFID was to make it cheap i.e. this is not economical that the object identifying system costs more than the actual worth of the object. After the invention of transistor the electronic device prices began to fall and it is possible to make cheap tags. Since RFID uses radio waves and radio waves are cheap and there are some other techniques that we can implement to produce cheap RFID tags e.g. †¢ No Transmitter. †¢ No Battery. †¢Read MoreEssay on Telecommunication Towers and Antennas1343 Words   |  6 Pagesto control radiation exposure from cell phone towers on a personal basis. Every day there is a growing body of scientific evidence that the electromagnetic radiation they emit, even at low levels, is dangerous to human health. The current U.S. standard for radiation exposure from cell phone towers is 580-1,000 microwatts per sq. cm. (mW/cm2). Since then, telecommunications businesses have been attempting to erect towers with antennas in or near almost every local community in order to provide